source: 2018/23/JesseS/JesseS/conf/svnserve.conf @ 9601

Revision 9601, 4.0 KB checked in by osedcald, 21 months ago (diff)
Line 
1### This file controls the configuration of the svnserve daemon, if you
2### use it to allow access to this repository.  (If you only allow
3### access through http: and/or file: URLs, then this file is
4### irrelevant.)
5
6### Visit http://subversion.apache.org/ for more information.
7
8[general]
9### The anon-access and auth-access options control access to the
10### repository for unauthenticated (a.k.a. anonymous) users and
11### authenticated users, respectively.
12### Valid values are "write", "read", and "none".
13### Setting the value to "none" prohibits both reading and writing;
14### "read" allows read-only access, and "write" allows complete
15### read/write access to the repository.
16### The sample settings below are the defaults and specify that anonymous
17### users have read-only access to the repository, while authenticated
18### users have read and write access to the repository.
19# anon-access = read
20# auth-access = write
21### The password-db option controls the location of the password
22### database file.  Unless you specify a path starting with a /,
23### the file's location is relative to the directory containing
24### this configuration file.
25### If SASL is enabled (see below), this file will NOT be used.
26### Uncomment the line below to use the default password file.
27# password-db = passwd
28### The authz-db option controls the location of the authorization
29### rules for path-based access control.  Unless you specify a path
30### starting with a /, the file's location is relative to the
31### directory containing this file.  The specified path may be a
32### repository relative URL (^/) or an absolute file:// URL to a text
33### file in a Subversion repository.  If you don't specify an authz-db,
34### no path-based access control is done.
35### Uncomment the line below to use the default authorization file.
36# authz-db = authz
37### The groups-db option controls the location of the groups file.
38### Unless you specify a path starting with a /, the file's location is
39### relative to the directory containing this file.  The specified path
40### may be a repository relative URL (^/) or an absolute file:// URL to a
41### text file in a Subversion repository.
42# groups-db = groups
43### This option specifies the authentication realm of the repository.
44### If two repositories have the same authentication realm, they should
45### have the same password database, and vice versa.  The default realm
46### is repository's uuid.
47# realm = My First Repository
48### The force-username-case option causes svnserve to case-normalize
49### usernames before comparing them against the authorization rules in the
50### authz-db file configured above.  Valid values are "upper" (to upper-
51### case the usernames), "lower" (to lowercase the usernames), and
52### "none" (to compare usernames as-is without case conversion, which
53### is the default behavior).
54# force-username-case = none
55### The hooks-env options specifies a path to the hook script environment
56### configuration file. This option overrides the per-repository default
57### and can be used to configure the hook script environment for multiple
58### repositories in a single file, if an absolute path is specified.
59### Unless you specify an absolute path, the file's location is relative
60### to the directory containing this file.
61# hooks-env = hooks-env
62
63[sasl]
64### This option specifies whether you want to use the Cyrus SASL
65### library for authentication. Default is false.
66### This section will be ignored if svnserve is not built with Cyrus
67### SASL support; to check, run 'svnserve --version' and look for a line
68### reading 'Cyrus SASL authentication is available.'
69# use-sasl = true
70### These options specify the desired strength of the security layer
71### that you want SASL to provide. 0 means no encryption, 1 means
72### integrity-checking only, values larger than 1 are correlated
73### to the effective key length for encryption (e.g. 128 means 128-bit
74### encryption). The values below are the defaults.
75# min-encryption = 0
76# max-encryption = 256
Note: See TracBrowser for help on using the repository browser.